2003 Nissan Altima

ON CERTAIN PASSENGER VEHICLES, THE CIRCUIT BOARD FOR THE CRANK POSITION SENSOR OR CAM POSITION SENSOR MAY HAVE AN IMPROPER SOLDER JOINT DUE TO SOLDER DEFORMATION CAUSED BY HEAT STRESS ACCELERATED BY THE EXISTENCE OF FLUX RESIDUE DURING THE SOLDERING PROCESS.

ON CERTAIN VEHICLES EQUIPPED WITH THE 2.5 LITER ENGINE, THE EXHAUST PIPE HANGER PIN MAY CATCH DEBRIS FROM THE ROAD THAT COULD BE IGNITED BY CONTACT WITH THE MAIN CATALYST. ALSO ON 2002 ALTIMA AND SENTRA VEHICLES, CERTAIN ENGINE OPERATING CONDITIONS MAY CAUSE THE PRE-CATALYST TO OVERHEAT AND DAMAGE THE CATALYST SUBSTRATE.

ON CERTAIN PASSENGER VEHICLES ORIGINALLY SOLD IN OR CURRENTLY REGISTERED IN THE STATES OF ALASKA, COLORADO, CONNECTICUT, IOWA, IDAHO, ILLINOIS, INDIANA, KANSAS, MASSACHUSETTS, MAINE, MICHIGAN, MINNESOTA, MISSOURI, MONTANA, NORTH DAKOTA, NEBRASKA, NEW HAMPSHIRE, NEW YORK, OHIO, PENNSYLVANIA, RHODE ISLAND, SOUTH DAKOTA, UTAH, VERMONT, WISCONSIN, AND WYOMING. AT EXTREMELY COLD TEMPERATURES, MOISTURE

CERTAIN ANZO COMBINATION HEADLAMP ASSEMBLIES SOLD AS REPLACEMENT LAMPS FOR USE ON CERTAIN PASSENGER VEHICLES. SOME COMBINATION LAMPS ARE NOT EQUIPPED WITH AMBER SIDE REFLECTORS WHICH FAIL TO CONFORM TO FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, "LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT."

ON CERTAIN PASSENGER VEHICLES EQUIPPED WITH A 2.5L ENGINE, THE CRANK ANGLE SENSOR IS AFFECTED BY TEMPERATURE VARIATIONS. UNDER CERTAIN DRIVING CONDITIONS, THESE VARIATIONS IN TEMPERATURE CAN BE LARGE ENOUGH TO CAUSE A BRIEF INTERRUPTION IN THE SIGNAL OUTPUT FROM THE SENSOR.

CERTAIN TRADESONIC COMBINATION LAMPS SOLD AS REPLACEMENT LAMPS FOR USE ON THE ABOVE LISTED PASSENGER VEHICLES. COMBINATION LAMPS NOT EQUIPPED WITH AMBER SIDE REFLECTORS FAIL TO CONFORM WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT.

CERTAIN ANZO AFTERMARKET HEADLIGHTS, P/N 02-AZ-NA02-B-A, SOLD FOR USE ON 2002-2004 NISSAN ALTIMA VEHICLES. DURING PRODUCTION THE LAMP HOUSING SHAPE DEFORMED DISTORTING THE ASSEMBLY ANGLE OF THE REFLECTOR AND INFLUENCED THE AIMING POSITION. THESE HEADLAMPS FAIL TO CONFORM TO THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT.

CERTAIN EAGLE EYES HEADLAMP ASSEMBLIES, P/NOS. DS517-B001L AND DS517-B001R, SOLD FOR USE AS REPLACEMENT EQUIPMENT FOR THE ABOVE LISTED PASSENGER VEHICLES. THE OPTICEL SURFACE OF THE REFLECTOR IS CORRODED INHIBITING THE PERFORMANCE OF THE UPPER AND LOWER BEAMS WHICH FAILS TO CONFORM TO THE PHOTOMETRIC REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, LAMPS, REFLECTIVE DEVICES, AND ASS

CERTAIN MAXZONE HEADLIGHT ASSEMBLIES, DEPO BRAND, P/NOS. 315-1145L-AS AND 315-1145R-AS, SOLD FOR USE AS AFTERMARKET EQUIPMENT FOR THE ABOVE LISTED PASSENGER VEHICLES. DURING PRODUCTION THE LAMP REFLECTOR SHAPE DEFORMED CHANGING THE SHAPE OF THE OPTIC SURFACE. THIS WILL CHANGE THE OPPOSITE POSITION OF LOW BEAM AND HIGH BEAM OPTICSAND CHANGE THE ANGLE OF INCIDENCE AND ILLUMATED LOCATION WHICH FAIL

SABERSPORT IS RECALLING 16,270 COMBINATION CORNER AND BUMPER LAMP ASSEMBLIES OF VARIOUS PART NUMBERS SOLD FOR USE AS AFTERMARKET EQUIPMENT FOR VARIOUS PASSENGER VEHICLES. THESE HEADLAMPS FAIL TO CONFORM TO THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, "LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT." THESE LAMPS DO NOT CONTAIN THE REQUIRED AMBER SIDE REFLECTORS.